Find the most up-to-date version of CEN – EN at Engineering Testing fresh concrete – Part 1: Sampling – SS-EN This European Standard specifies two procedures for sampling fresh concrete, by composite. 1 Apr This British Standard specifies two procedures for sampling fresh concrete which are implemented by composite sampling and by spot.
|Published (Last):||24 April 2013|
|PDF File Size:||9.21 Mb|
|ePub File Size:||12.3 Mb|
|Price:||Free* [*Free Regsitration Required]|
Full compaction is achieved using mechanical vibration, 123550-1 there no further appearance of large air bubbles on the surface of the en 12350-1 and the surface becomes relatively smooth with a glazed en 12350-1, without excessive segregation.
en 12350-1 Take en 12350-1 scoopfuls of concrete through the moving stream from truck mixer. Your basket is empty. Materials handling, Test specimens, Sampling methods, Concretes, Samples, Cement and concrete technology. Avoid over-vibration, which may cause loss of en 12350-1 air. The place else may anybody get that type of info in such a perfect means of writing? A sample of concrete is placed in a mold, shaped as the frustum of a cone, and compacted. Foreword Scope Normative references Terms and definitions Apparatus Sampling Report of sampling See more standards on testing concrete.
For this to occur the delay should be sufficient for the lower layer to develop an initial set or harden. Half of the strokes en 12350-1 perimeter, and then progressing with vertical strokes spirally en 12350-1 the center.
Accept and continue Learn more about the cookies we use and how to change your settings. Leave a Reply Cancel reply Enter your comment here You may find similar items within these categories by selecting from the choices below:. You are en 12350-1 using your WordPress. Sampling BS EN specifies two procedures for sampling fresh concrete, by composite sampling and by spot sampling. Metallic, Frustum of a cone Alternative materials are allowed if requirements are met comparability tests Tamping Rod Round, straight steel rod, length mm and diameter 16mm En 12350-1 end rounded to a hemispherical tip Measuring Device Ruler Marked in increments of 5 mm or smaller Length of at least mm In addition, a scoop is needed.
Concrete and concrete products. Concrete cubes at the site Marking The test specimens shall be marked clearly and indelibly, without damaging the specimen using a cub tag that contains the en 12350-1 related to the specimen Casting date, ticket number, specimen ID, location of sampling….
Email required Address en 12350-1 made en 12350-1. Depending on the consistency of the concrete and the method of compaction, moulds shall be filled in one or more layers to achieve full compaction. Shopping 123501- Close cart 0, foreach: This British Standard specifies two procedures for sampling fresh concrete which are implemented by composite sampling and by spot sampling.
Customers who en 12350-1 this product also bought BS EN Surface leveling Remove the excess concrete above the upper en 12350-1 of the mould using the steel trowel or float and carefully level the surface.
You may experience issues viewing this site e Internet Explorer 9, 10 or See more standards on testing concrete.
Sampling of Freshly Mixed Concrete at the Field (BS EN ) – QA/QC Construction
Worldwide Standards We can source any standard from anywhere in the world. Plastic concrete slump greater than en 12350-1 mm and less than en 12350-1.
Raise the mold carefully in a vertical direction with no lateral or torsional motion Raise the mold in 2 to 5 sec. There is often debate about the time limit between placing fresh concrete against fresh concrete already placed and compacted i. Both parties will en 12350-1 to the specific time limit as substantiated from the concrete design mix.
Learn more about the cookies we en 12350-1 and how to change your settings. Quantity at least 1. The requirement for remixing the sample before tests on the fresh concrete, or before making test specimens, is included in the relevant standards. Notify me of new 12305-1 via email. Take the smart route en 12350-1 manage medical device compliance. Records shall be kept to ensure the traceability of the specimen from sampling to testing.
After compaction of each layer, tap the sides of the en 12350-1 smartly with the mallet until large bubbles of air cease to appear on the surface and depressions left en 12350-1 dn compacting rod or bar, are removed. Leave the TMD in the concrete a en 12350-1 of 2 min. Immediately measure the vertical difference between the height of the mould and that of the highest point of the slumped test specimen. Each sample shall be accompanied by a report from the person responsible for taking the sample.
Mechanical vibration with vibrating table Apply the vibration for the minimum en 12350-1 necessary to achieve full compaction of the concrete. This test is considered applicable to: Procedure Place the TMD in the concrete so that the sensing portion en 12350-1 submerged 12350-11 minimum of 75 mm.
BS EN 12350-1:2009
Search all products by. This website is best viewed with browser version 1235-1 up en 12350-1 Microsoft Internet Explorer en 12350-1 or Firefox 3.
Strike off the mold with the tamping rod in a screeding and rolling motion Remove concrete from the area surrounding the base to prevent interference with the movement of slumping concrete.